New England School of Metalwork
7 Albiston Way Auburn, Maine 04210
207-777-6211 Toll Free 888-753-7502
Fax 207-784-5383

ITEMS

 

COAL FORGES

       These coal forges are extras produced with loving care at one of our Coal Forge Building workshop.  It features a rugged Centaur Forge fire pot, 275 CFM shaded pole blower, 5 feet of tool rung, 16" adjustable stock rest, custom blast gate and variable fan control w/ 10' cord.  Constructed of sturdy 1/4" thick angle iron and 3/16" plate. It measures 48"X"x34" tall. A very generous table size. It weighs about 200 lbs. All yours for     $750.00

The Coal Forge Building Workshop is being offered to you, March 26-28  FULL

Build your own forge for $500.00 

None in stock, build to order

 

    Beginners  Blacksmithing Tool Kit

 

Beginners  Blacksmithing Tool Kit

High quality forged tools forged here at the school 
by Blacksmiths for Blacksmiths

Custom tool tote holds:

900 gram Cross Peen
Grooved Flat Jaw Tongs
Bidirectional V-Bit Tongs
Alloy Steel Bending Fork
Bending U
Hot Cut Chisel
Round Hot Punch
Cold Chisel
Center Punch

Beginners Tool Kit $275.00             4 in stock

Wrought Iron Bar

This material was reclaimed by Liberty Salvage two years ago. From a local turn of the century mill building across the river in Lewiston. It forges very well with little or no splitting, has a very lively pattern and welds beautifully. We have 1 1/2"(6 lb./ft)and 1 3/4" round bar (8 pounds/ft). We also will forge down to size for you. The unforged bar is $4.00 per pound, call for forged pricing (207)777-3375. We have sold several thousand pounds to bladesmiths as well as blacksmiths for reproduction work.There is about 15 tons available.

    

          

 

 

Quench Tubs

       There are a limited number of these beauties. Made from the outer skin of liquid oxygen packs. They are made of 1/8" mild steel with a rugged base. Each measures approx. 20" in diameter and 24" tall. These hold allot of water and are very stable. 

$ 40.00                                                                  1 in stock

Also available but not pictured, 16" diameter by 24" tall tubs.

$30.00                                                             4 in stock

 COAL

      We are now careering coal for sale to YOU. It has become quite obvious how difficult it can be to find good coal. We are shipping our coal in from William's Coal in Braintree MA. It is good coal, low clinker, low sulfur and medium to low ash content. It is pre bagged in 55 lb. bags. To cover our cost and the freight they are $15.00 per bag. Please call the school to schedule pick up, 207-777-3375. 

 

       *** Anvil not included.***

 

 

Setco Industries Pedestal Grinder

NEED GRINDING POWER??

This is a SETCO INDUSTRIES 16"

Pedestal grinder. Up to 3" wide wheels. 3 HP, 9 amps, 1800 rpm

It requires 3 phase and comes with a heavy duty starter and switch box.

American made in Cincinnati, Ohio

Could be a great knife grinder.

Very good condition  $300.00

 

 

Clonzt / Spencer Tire Hammer


This Little Giant clone power hammer is one of many out in the service of busy blacksmith's all over the country. It features a small two foot square base, full size six inch diameter anvil, frame is all 5/16 thick wall tube, quality 1725 rpm 110 volt motor, all steel, welded construction, bolt on dies of 4140. This hammer is capable of up to 220 beats per minute OR single blows via the fully adjustable brake, you set the clutch slippage for your comfort. It is a little over seven feet tall and weighs in at about 700 pounds. We have extras from our Hammer Building Workshops. Very controllable and rugged.

NONE in Stock at this point, call with interest. We want to run this class again, your interest can make that happen!!

We will pack and ship this to you, provide your zip code to get a freight cost.